10' 15 Series (150A) MIG Welding Gun w/Two Female Spade Terminal Trigger Connection

Product # 81295B
  • Regular priceList
    $125.00
  • Price:
  • $82.95
  • You Save: $42.05 !


    Description:

    10' 15 Series (150A at 25% duty-cycle) MIG welding gun. Uses HTP America® 15 Series consumables (the traditional 15 Series gas diffuser is not compatible with this gun; for the gas diffuser used with this gun, please visit the following link: Female Gas Diffuser f/81295B MIG Welding Gun). Fits many small (and typically Italian-made) MIG welders. Features a gas valve in the brass block at the base of the swan neck, located within the handle, since the machines do not include a built-in solenoid valve. The ring terminal connects to a stud on the inside of the machine, the two female spade terminal trigger wires connect to the trigger terminal on the inside of the machine, and the gas hose runs through the machine and to the adapter on the backside of the machine.



    Customer Reviews
    4.8 Based on 16 Reviews
    5 ★
    88% 
    14
    4 ★
    6% 
    1
    3 ★
    6% 
    1
    2 ★
    0% 
    0
    1 ★
    0% 
    0
    Write a Review

    Thank you for submitting a review!

    Your input is very much appreciated. Share it with your friends so they can enjoy it too!

    Filter Reviews:
    MY
    02/04/2024
    Michael Y.
    United States United States

    Great gun

    Made the harbor freight welder 100% better able to activate gun like it should It never worked correctly before recommended to anybody if there HF MiG gun is acting up I also replaced the ground clamp and cable with HTP one I can tack a lot better The trigger would activate with inconsistently Very quick shipping and they were very nice on the phone Great place to shop

    RB
    11/27/2023
    Rob B.
    United States United States

    Clarke MIG 100EE MK2

    Needed a new gun for this 25+ year old welder and this is a great solution. Purchased this gun and installation was super easy. -I did need to trim about an 1 inch off the wire feed tube so it didn't make contact with the wire feed wheel. Rather than risk crushing the tubing with a pair of hand cutters, I using a cut-off wheel as to not damage the diameter of the tubing. -The reason this tubing trimming was required was because of where the plastic insert (prevents the hose from pulling on the wires inside the machine) is located on the inside of the outer protective cover. This insert must be located in the end of the wire feed assembly and positioning this properly makes the metal fire feed tube longer than the wire feed wheel. - The electrical connections are simple. The brown where replaces the existing brown wire. Just pull the old connector off of the electrical spade on the machine and replace with the new wiring brown wire. - Since this was originally a one control wire machine, I connect the blue wire to the open spade on the metal bar that the main electrode connects to. There's another writeup here that they tied into the power wire itself, if you use the open spade that is on the machine, you don't need to cut any electrical connectors of the replacement gun.

    RB
    11/27/2023
    Rob B.
    United States United States

    Replacement gun for Clarke MIG 100E MK2

    Needed a new gun for this 25+ year old welder and this is a great solution. Purchased this gun and installation was super easy. -I did need to trim about an 1 inch off the wire feed tube so it didn't make contact with the wire feed wheel. Rather than risk crushing the tubing with a pair of hand cutters, I using a cut-off wheel as to not damage the diameter of the tubing. -The reason this tubing trimming was required was because of where the plastic insert (prevents the hose from pulling on the wires inside the machine) is located on the inside of the outer protective cover. This insert must be located in the end of the wire feed assembly and positioning this properly makes the metal fire feed tube longer than the wire feed wheel. - The electrical connections are simple. The brown where replaces the existing brown wire. Just pull the old connector off of the electrical spade on the machine and replace with the new wiring brown wire. - Since this was originally a one control wire machine, I connect the blue wire to the open spade on the metal bar that the main electrode connects to. There's another writeup here that they tied into the power wire itself, if you use the open spade that is on the machine, you don't need to cut any electrical connectors of the replacement gun.

    MH
    06/11/2023
    Marion H.
    United States United States

    Excellent replacement for my MatCo gun

    The equipment worked very well. I did have to make an adjustment to ensure that the main liner was gripped effectively in the drive system. After that adjustment (addition of a sleeve to better clamp the liner before the feed rollers), the unit works exceptionally well and is much better than the original unit that it replaces.

    DS
    02/02/2023
    DONALD S.
    United States United States

    Donald

    Works great Will order from you if needed in the future